Get A Quote

 

 

We have noticed the article relating to How to Install a Bathtub Yourself listed below on the internet and felt it made good sense to write about it with you on this site.

Installing a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately tough project. If the old tub is conveniently easily accessible, the task can relocate rapidly; if you need to open a wall to eliminate the old bathtub and also place the new bathtub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. Make certain you have actually qualified on your own for the task and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to consider employing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly help you install a brand-new bath tub in your restroom if you have actually currently acquired a brand-new tub and also don't need to change the arrangement of your previous water supply pipes.
Your devices and also product checklist ought to consist of the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Planning for the Installation

First of all, the supporting framework supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will come from the pipes. When the supply pipelines have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from turning during this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

 

 

Installing the Bath tub

Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub till the spirit level checks out level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Activate the water system as well as check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the tub ought to wait till the tub has been made use of a minimum of when as this will settle it right into its last setting.

 

 

Fitting New Taps

If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to permeate the wall in between the bathroom and also the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant sticky and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

Hopefully you enjoyed our section about A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for spending some time to read our piece of content. Please take the opportunity to distribute this blog entry if you enjoyed it. Thanks a lot for going through it.

This Resource